redpitaya-puzzlefw/os/devicetree/redpitaya_puzzlefw.dts

214 lines
3.7 KiB
Plaintext
Raw Normal View History

2024-01-07 00:52:36 +01:00
/*
* Device tree for Red Pitaya PuzzleFw firmware.
*/
/dts-v1/;
// Include defaults from Linux kernel source tree.
/include/ "zynq-7000.dtsi"
/ {
model = "RedPitaya PuzzleFW";
compatible = "xlnx,zynq-7000";
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
aliases {
ethernet0 = &gem0;
i2c0 = &i2c0;
serial0 = &uart0;
mmc0 = &sdhci0;
};
// Red Pitaya: 512 MByte DDR RAM at address 0x00000000
memory@0 {
device_type = "memory";
reg = <0x0 0x20000000>;
};
// Red Pitaya: 2 LEDs controlled by PS
gpio-leds {
compatible = "gpio-leds";
led-8-yellow {
label = "led8";
gpios = <&gpio0 0 0>;
default-state = "off";
linux,default-trigger = "mmc0";
};
led-9-red {
label = "led9";
gpios = <&gpio0 7 0>;
default-state = "off";
linux,default-trigger = "heartbeat";
};
};
usb_phy0: phy0 {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
// Reserved memory for DMA buffers
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
puzzlefw_mem: puzzlefw_mem@14000000 {
// compatible = "jigsaw,puzzlefw";
reg = <0x14000000 0x4000000>; // 64 MByte
//size = <0x4000000>; // 64 MByte
//alignment = <0x100000>; // 1 MByte
no-map;
};
};
2024-01-07 00:52:36 +01:00
// Register range and interrupts for FPGA logic
puzzlefw@43000000 {
#address-cells = <1>;
#size-cells = <1>;
2024-01-07 00:52:36 +01:00
compatible = "jigsaw,puzzlefw";
status = "okay";
2024-01-07 00:52:36 +01:00
//
// Register address mapping:
//
// Address 0x43000000 .. 0x430fffff (1 MB) = user registers
// Address 0x43100000 .. 0x43100fff (4 kB) = setup registers
//
reg = <0x43000000 0x100000>,
<0x43100000 0x1000>;
2024-01-07 00:52:36 +01:00
//
// The FPGA firmware uses interrupts
// IRQ_F2P[0] .. IRQ_F2P[3]
//
// These correspond to IRQ 61 .. 64 in the GIC.
//
// The format <0 29 4> means the following:
// 0 : denotes an SPI interrupt (shared peripheral)
// 29 : the kernel adds 32 to this value to get 29+32 = 61
// 4 : IRQ_TYPE_LEVEL_HIGH (level sensitive interrupt)
//
interrupt-parent = <&intc>;
interrupts = <0 29 4>,
<0 30 4>,
<0 31 4>,
<0 32 4>;
//
// Claim DMA buffer.
//
memory-region = <&puzzlefw_mem>;
2024-01-07 00:52:36 +01:00
};
};
&gem0 {
status = "okay";
xlnx,ptp-enet-clock = <0x69f6bcb>;
phy-mode = "rgmii-id";
phy-handle = <&ethernet_phy>;
// Red Pitaya: Lantiq Ethernet PHY, MDIO address 1
ethernet_phy: ethernet-phy@1 {
reg = <1>;
device_type = "ethernet-phy";
};
};
&gpio0 {
emio-gpio-width = <24>;
gpio-mask-high = <0x0>;
gpio-mask-low = <0x5600>;
};
&i2c0 {
status = "okay";
clock-frequency = <100000>;
2024-01-07 00:52:36 +01:00
// Red Pitaya: EEPROM chip on internal I2C bus.
eeprom@50 {
compatible = "24c64";
reg = <0x50>;
pagesize = <32>;
};
};
&intc {
num_cpus = <2>;
num_interrupts = <96>;
};
&qspi {
status = "okay";
is-dual = <0>;
num-cs = <1>;
spi-rx-bus-width = <4>;
spi-tx-bus-width = <4>;
};
&sdhci0 {
status = "okay";
xlnx,has-cd = <0x1>;
xlnx,has-power = <0x1>;
xlnx,has-wp = <0x1>;
};
&spi0 {
status = "okay";
2024-01-07 00:52:36 +01:00
is-decoded-cs = <0>;
num-cs = <3>;
};
&spi1 {
status = "okay";
2024-01-07 00:52:36 +01:00
is-decoded-cs = <0>;
num-cs = <1>;
};
&uart0 {
status = "okay";
device_type = "serial";
cts-override;
};
&uart1 {
status = "okay";
device_type = "serial";
cts-override;
};
&usb0 {
status = "okay";
phy_type = "ulpi";
dr_mode = "host";
usb-phy = <&usb_phy0>;
usb-reset = <&gpio0 48 0>;
};
&clkc {
fclk-enable = <0x1>;
ps-clk-frequency = <33333333>;
};
&devcfg {
// Override clock list.
clocks = <&clkc 12>, <&clkc 15>, <&clkc 16>, <&clkc 17>, <&clkc 18>;
clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3";
};
/*
TODO -- later
&watchdog0{
status = "okay";
reset-on-timeout;
};
*/