redpitaya-puzzlefw/os/devicetree/redpitaya_puzzlefw.dts

/*
 * Device tree for Red Pitaya PuzzleFw firmware.
 */

/dts-v1/;

// Include defaults from Linux kernel source tree.
/include/ "zynq-7000.dtsi"

/ {
	model = "RedPitaya PuzzleFW";
	compatible = "xlnx,zynq-7000";

	chosen {
		bootargs = "earlycon";
		stdout-path = "serial0:115200n8";
	};

	aliases {
		ethernet0 = &gem0;
		i2c0 = &i2c0;
		serial0 = &uart0;
		mmc0 = &sdhci0;
	};

	// Red Pitaya: 512 MByte DDR RAM at address 0x00000000
	memory@0 {
		device_type = "memory";
		reg = <0x0 0x20000000>;
	};

	// Red Pitaya: 2 LEDs controlled by PS
	gpio-leds {
		compatible = "gpio-leds";
		led-8-yellow {
			label = "led8";
			gpios = <&gpio0 0 0>;
			default-state = "off";
			linux,default-trigger = "mmc0";
		};
		led-9-red {
			label = "led9";
			gpios = <&gpio0 7 0>;
			default-state = "off";
			linux,default-trigger = "heartbeat";
		};
	};

	usb_phy0: phy0 {
		compatible = "usb-nop-xceiv";
		#phy-cells = <0>;
	};

	// Register range and interrupts for FPGA logic
	puzzlefw@43c00000 {
		compatible = "jigsaw,puzzlefw";
		//
		// Register address mapping:
		//
		// Address 0x43000000 .. 0x430fffff (1 MB) = user registers
		// Address 0x43100000 .. 0x43100fff (4 kB) = setup registers
		//
		reg = <0x43000000 0x100000>,
		      <0x43100000 0x1000>;
		//
		// The FPGA firmware uses interrupts
		//   IRQ_F2P[0] .. IRQ_F2P[3]
		//
		// These correspond to IRQ 61 .. 64 in the GIC.
		//
                // The format <0 29 4> means the following:
                //    0 : denotes an SPI interrupt (shared peripheral)
                //   29 : the kernel adds 32 to this value to get 29+32 = 61
                //    4 : IRQ_TYPE_LEVEL_HIGH (level sensitive interrupt)
		//
		interrupt-parent = <&intc>;
		interrupts = <0 29 4>,
		             <0 30 4>,
		             <0 31 4>,
		             <0 32 4>;
	};

	// Reserved memory for DMA buffers
	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		puzzlefw {
			compatible = "jigsaw,puzzlefw";
			size = <0x4000000>;     // 64 MByte
			alignment = <0x100000>; //  1 MByte
			no-map;
		};
	};

};

&gem0 {
	status = "okay";
	xlnx,ptp-enet-clock = <0x69f6bcb>;
	phy-mode = "rgmii-id";
	phy-handle = <&ethernet_phy>;

	// Red Pitaya: Lantiq Ethernet PHY, MDIO address 1
	ethernet_phy: ethernet-phy@1 {
		reg = <1>;
		device_type = "ethernet-phy";
	};
};

&gpio0 {
	emio-gpio-width = <24>;
	gpio-mask-high = <0x0>;
	gpio-mask-low = <0x5600>;
};

&i2c0 {
	status = "okay";

	// Red Pitaya: EEPROM chip on internal I2C bus.

	eeprom@50 {
		compatible = "24c64";
		reg = <0x50>;
		pagesize = <32>;
	};

/*
	eeprom@51 {
		compatible = "24c64";
		reg = <0x51>;
		pagesize = <32>;
	};
*/
};

&intc {
	num_cpus = <2>;
	num_interrupts = <96>;
};

&qspi {
	status = "okay";
	is-dual = <0>;
	num-cs = <1>;
	spi-rx-bus-width = <4>;
	spi-tx-bus-width = <4>;
};

&sdhci0 {
	status = "okay";
	xlnx,has-cd = <0x1>;
	xlnx,has-power = <0x1>;
	xlnx,has-wp = <0x1>;
};

&spi0 {
	is-decoded-cs = <0>;
	num-cs = <3>;
	status = "okay";
};

&spi1 {
	is-decoded-cs = <0>;
	num-cs = <1>;
	status = "okay";
};

&uart0 {
	status = "okay";
	device_type = "serial";
	cts-override;
};

&uart1 {
	status = "okay";
	device_type = "serial";
	cts-override;
};

&usb0 {
	status = "okay";
	phy_type = "ulpi";
	dr_mode = "host";
        usb-phy = <&usb_phy0>;
	usb-reset = <&gpio0 48 0>;
};

&clkc {
	fclk-enable = <0x1>;
	ps-clk-frequency = <33333333>;
};

&devcfg {
	// Override clock list.
	clocks = <&clkc 12>, <&clkc 15>, <&clkc 16>, <&clkc 17>, <&clkc 18>;
	clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3";
};

/*
TODO -- later
&watchdog0{
	status = "okay";
	reset-on-timeout;
};
*/